Category: Free 642-883 Study Test

Free 642-883 Study Test

Preparing Cisco 642-883 exam is not difficult now. You can prepare from Cisco 642-883 Books or 642-883 dumps. Here we have mentioned some sample questions. You can use our free 642-883 study material notes for test preparation. Latest 642-883 study material available.


642-883 Dumps

Preparing Cisco 642-883 exam is not a big deal now with our 642-883 braindumps. You can prepare from officially recommended Cisco 642-883 Books or 642-883 dumps. Here at Cisexams.com, we have mentioned some free 642-883 Questions Answers. You can use our free Cisco 642-883 Study Material to get an idea about the quality and validity of this resource. Our Cisco 642-883 PDF and 642-883 dumps practice tests have helped thousands of candidates from all around the world to get their desired certification. Latest 642-883 Real Exam Questions are available with 100% money back guarantee. You have nothing to lose now!!!

642-883 | When implementing OSPF, which type of networks…

Question: 7

When implementing OSPF, which type of networks require DR/BDR election?

A. point-to-point networks
B. mutli-access broadcast networks
C. non-broadcast multi-access networks (Hub and Spoke Frame Relay) using point-to-multipoint OSPF network type
D. All networks type

Answer: B

642-883 | In comparing IS-IS with OSPF…

Question: 6

In comparing IS-IS with OSPF, a Level-1-2 IS-IS router is similar to which kind of OSPF router?

A. ASBR on a normal OSPF area
B. ASBR on NSSA
C. ABR on totally stubby OSPF area
D. ABR on stubby OSPF area
E. ABR on a normal OSPF area

Answer: C

642-883 | Which two OSPF network scenarios…

Question: 5

Which two OSPF network scenarios require OSPF virtual link configuration? (Choose two.)

A. to connect an OSPF non-backbone area to area 0 through another non-backbone area
B. to connect an NSSA area to an external routing domain
C. to connect two parts of a partitioned backbone area through a non-backbone area
D. to enable route leaking from Level 2 into Level 1
E. to enable route leaking from Level 1 into Level 2
F. to enable OSPF traffic engineering

Answer: A,C

642-883 | Which two OSPF network scenarios require OSPF virtual link configuration?

Question No : 4

Which two OSPF network scenarios require OSPF virtual link configuration? (Choose two.)

A. to connect an OSPF non-backbone area to area 0 through another non-backbone area
B. to connect an NSSA area to an external routing domain
C. to connect two parts of a partitioned backbone area through a non-backbone area
D. to enable route leaking from Level 2 into Level 1
E. to enable route leaking from Level 1 into Level 2
F. to enable OSPF traffic engineering

Answer : A,C

642-883 | Which three statements are true regarding the OSPF router ID?

Question No : 3

Which three statements are true regarding the OSPF router ID? (Choose three.)

A. The OSPF routing process chooses a router ID for itself when it starts up.
B. The router-id command is the preferred procedure to set the router ID.
C. If a loopback interface is configured, its address will always be preferred as the router ID over any other methods.
D. After the router ID is set, it does not change, even if the interface that the router is using for the router ID goes down. The router ID changes only if the router reloads or if the OSPF routing process restarts.
E. In OSPF version 3, the OSPF router ID uses a 128-bit number.

Answer : A,B,D

642-883 | On Cisco IOS XR Software, which set of commands is used to enable the gi0/0/0/1 interface for OSPF in area 0?

Question No : 2

On Cisco IOS XR Software, which set of commands is used to enable the gi0/0/0/1 interface for OSPF in area 0?

A. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ! router ospf 1 network 10.1.1.1 0.0.0.0 area 0
B. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ! router ospf 1 network 10.1.1.1 255.255.255.255 area 0
C. router ospf 1 area 0 interface GigabitEthernet0/0/0/1
D. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ip ospf 1 area 0
E. router ospf 1 address-family ipv4 unicast interface GigabitEthernet0/0/0/1 area 0
F. router ospf 1 address-family ipv4 unicast interface GigabitEthernet0/0/0/1 area 0

Answer : C

642-883 | When troubleshooting OSPF neighbor errors, which three verification steps should be considered?

Question No : 1

When troubleshooting OSPF neighbor errors, which three verification steps should be considered? (Choose three.)

A. Verify if neighboring OSPF interfaces are configured in the same area.
B. Verify if neighboring OSPF interfaces are configured with the same OSPF process ID.
C. Verify if neighboring OSPF interfaces are configured with the same OSPF priority.
D. Verify if neighboring OSPF interfaces are configured with the same hello and dead intervals.
E. Verify if neighboring OSPF interfaces are configured with the same area type.

Answer : A,D,E